Which of the following statements describbe(S) limitation (S) of concrete technology?
A) Availability of concrete ingredients easily
B) Due to low tensile strength, concrete is requured to be reinfored to avod cracks
C) Monolithic character gives better appearance.
D) The property of concrete possess high compressive strength
A,B and C
B and C
only B
only C
Which of the following statements is/are incorrect about the prismatic compass?
A) The needle is broad but it does not act as an index.
B) The graduated ring is attached with the needle This does not rotate along with the line of sight
c) The readings are taken directly seeing through the top of the glass
only A
A and C
Accprding to geological classification, rocks are divided into three different categories i.e, Igneous rocks, sedimemtary rocks and metamorphic rocks In which category Granite,
Sedimentary rocks
Metamorphic rocks
Igenous rocks
Stratified rocks
Which of the following is/are not the characteristic (s) of an ideal reinforcing material?
A) It should be easily available in bulk and at low prices
B) It should not possess high tensile stress and elasticity
c) It should be free from loose mill scales, loose rust and coat of paints
A and B
Which of the following is/are the property (s) of good quality of stones?
A) Crushing strength greater than 1000kg/CM2
B) Specific gravity should be greater then 8
C) stone should be well seasoned before putting into use
The shear strength is a most important characteristic of the soil. What is/are the correct reason (S) dur ti which the shear resistance of the soil occurs?
A)cohesion
B) structural resistance
C) Friction
A,B and c
Which of the following statements is/are not corret as per the requirements specified by IS: 383-1970, for an ideal aggregate used for manufacturing of concrete?
A) It should be hard, strong and durable
B) It should contain flaky and elongated pieces
C) It should be dense, clear and free from any coating
D) It should consist of natural stones, gravels and sand
B and D
Why steel is commonly used as good reinforcing material?
A) It is cheaply available in bulk
B) Thermal cofficient is nearly equal to concrete
C) It possesses low tensile strength
D) It develops good bond with concrete
only c
A,B and D
A and D
Which of the following factors affect(s) the per capita demand of water?
A) Climatic conditions of the region
B) Industrial/commercial activities of the region
C) Population
Only A
which of the following statements is/are tute about the types of gauge in India Railways?
1)In Broad gauge, the clear distance between the inner faces of two rails is 1.676 m
2)In Meter gauge the clear distance between the inner faces of two rails is 1.240 m
3)In Narrow gauge. the clear distance between the inner faces of two rails is 0.762 m
I,II and III
I and III
I and II
only I
According to the assumptions of Terzaghi's one-Dimensional consolidation Theory, which of the following statements is/are incorrect?
The soil is homogeneous
The soil is 100% unsaturated
The soil is laterally confined
which of the following statements is/are not among the major limitations of sprinkler irrigation?
storng wind disturbs the sprinkling
It requires heavy initial investment
It minimizes the erosion oof the soil
An activated carbon is specially treated carbon which has the property of absorbing and attracting impurities. Which of the following points is/are not among the advantages of activated?
It minimises the chlorine demand of treated water
It accelerates the coagulation
Its overdoes is harmful
__________is the type of concrete in which internal stresses are intentionally induced in a planned manner such that the stresses resulting from the superimposed loads get counteracted to a desired degree.
Post-stressed concrete
Intra-stressed concrete
Curvatured concrete
Pre-stressed concrete
A train has to run on a BG track having a curvature of 3 degrees and cant of 100 mm. What would be the maximum permissible speed of this train if the allowable cant deficiency is 76 mm?
98.2 kmph
78.2 kmph
68.2 kmph
88.2 kmph
_____________ is the crude impure iron, which is extracted from iron ores.
Steel
Cast iron
Pig iron
Wrought iron
__________ is the geological formation that does not yield water freely to well due to its lesser permeability.
Aquatic permeability
Aquifer
Acquitard
Aquiclude
What is the name of the process in which reducing chemical such as sulphur dioxode (SO2), sodium trisulphite (NaHSO3) and sodium sulphit (Na2SO3) is added to remove unwanted residual of chlorine from water?
Chlorination
Hydrogenation
Dechlorination
Sulphurification
Which type of beam is supported only at one end by being built into a wall?
Overhanging beam
Cantilever beam
Curvature beam
Centroid beam
Which of the following characteristics of the rain strom can completely describe the rainfall at a place?
A. Intensity of the rain.
B. Duration of the rain.
C. Hyetograph.
D. Frequency of the rain.
Only C
A, B, C and D
The shear strength is a most important characteristic of the soil. What is/are the correct reason(s) due to which the shear resistance of the soil occurs?
A. Cohesion
B. Structural resistance
C. Friction
A, B and C
Which of the following statements is/are not correct as per the requirements specified by IS: 383-1970, for an ideal aggregate used for manufacturing of concrete?
A. It should be hard, strong and durable.
B. It should contain flaky and elongated pieces.
C. It should be dense, clear and free from any coating.
D. It should consist of natural stones, gravels and sand.
In an open field two parallel pipe lines are to be connected by a reverse curve, each section having the same radius. If the centre lines are 20 m apart, and the maximum distance between tangent points is 40 m, what is the maximum allowable radius that can be used?
20 m
40 m
32 m
60 m
In the Soil Mechanics and Foundation Engineering, the ratio of the density of solid to that of water at a given temperature is termed as___________ of soil solids.
specific gravity
porosity
degree of saturation
void ratio
The type of concrete in which preliminary tests are performed for designing the mix and it is also used for all the seven types of grades of cement is known as:
Nominal mix concrete
Controlled concrete
Ordinary concrete
Design mix concrete
A project engineer receives a laboratory report of a sample of soil having moist unit weight of a soil is 20.5 kN/m3, water content available is 25% and the specific gravity of the solid of the soil is 3.35. Find the dry unit weight of the soil.
16.8 kN/m3
18.4 kN/m3
18.8 kN/m3
16.4 kN/m3
A. It is cheaply available in bulk.
B. Thermal coefficient is nearly equal to concrete.
C It posssesses low tensile strength.
D. It develops good bond with concrete.
Select the correct option.
A, B and D
Four engineers, designated as CE, SE, EE and AE a certain number of newspapers early in the moring. One of them reads four newspapers, anothher reaeds three newspaper, the third reads two newspapres while the fourth one newspaper. Below are some additional fact reharding the names of these officers.
a)N is not the EE
b)H is the AE
c)N is not the CE and he reads more number of newspaper thnan L
d)The one who is the CE reads more number of newspaper thanL
e)The person who is the SE reads the maximum number of newspapers
f)B dose not read two newspapers
L is the EE and reads one newspaper
B is the CE and reads three newspapres
N is the EE and reads four newspapers
H is the AE and reads two newspapers
In a certain code FIRE is coded as DGPC. what is the last latter of the coded word for SHOT?
R
S
P
Q
If p's mother is Q's daughter, L is the maternal aunt of p, and M is the sister of Q, then how is M related to L?
mother-in-law
aunt
sister
daughter
In a certain code TOUR is coded as CLEAR as SPARE. What is the fifth digit for SCULOTURE?
4
6
0
1
Select from the given choices the letter sequence that completes the follwing sequence in an order. m n_ _m n n_ m n_ m
m n n m
n m m n
n n m m
m n m n
student X rank fifth from the top and nineteenth from the bottom in a class. How many students are there in the class?
24
21
23
22
Determaine the pattern and fill in the missing number. 5,9,17,33_
38
46
65
36
Identify the similar set of numbers (482,496,526)
(334,348,378)
(830,748,923)
(442,182,290)
(296,310,480)
After starting from a point, a man walks 3 km East, then turing to his left he moves 3 km . After this he again turns left and moves 3km Which choice given below indicates the corret direction in wich he is from his string point?
East
North
south
west
Russia related to Moscow in the same way France is releted to_
Paris
Rome
Havana
cario
In computer terminology, the full form of LNA is :
Local Area Network
Local Area Navigator
Laocal Alignment Network
Light Amplification Network
which Indian king was known as INdian Napolean?
Tipu Sultan
Babar
Krishnadevaraya
Samudragupta
In which state Indian Government has decided to establish oraganic farming research Institute?
Orissa
Tamil Nadu
Jharkhand
sikkim
Which south Indian actor served s as Tourism Ministar of India in UPA government?
K.Chiranjeevi
Mammotty
Kamal Hassan
Mohan Lal
who was the Chairman of the drafting committee for Indian Constitution?
Indira Gandhi
Dr.Bb.R Ambedakar
Sarvepalli Radha Krishnan
Lala Lajpat Rai
Who is considered as the Father of Modern Economics?
P.C Ray
Satyardhi
Adam Smith
Karl Marx
The highest rice producing state in India is
West Bengal
Telangana
In which year National Rual Employment Guarantee Act was introduced?
2010
2005
1999
2007
Which og the following Indian scientists discovered that stimuli in plants are due to electrical impulses?
C.V Raman
J.C Bose
Hargobind Khurana
Y.Subbba Rao
Which of the following fundanental rights is deleted from Indian constitution by the 44th amendmaent act?
Right to speak
Right against exploitation
Rght to vote
Right to property
what is the name of the method of design of a reinforced cement struture in which optimum use of inherent stregth of both steel and concrete is made?
Rcc stress desin
Axially loaded design
OPtimum load design
Ultimate load strength design
In the pile foundatio, which type of pile act as columns and transmit the load through weak soil to a firm stratum at a greater depth?
Footing piles
End bearing piles
Compaction piles
Friction piles
According to the level of pressure applied, lateral earth pressure is classified into various types. which of the following type of latral earth pressure to the minimum pressure exerted by the soil on the retainomg wall?
Earth pressure at rest
Active earth pressure
passive earth pressure
Cylindrical earth pressure
_ is an engineered material that contains cement polymers, and glass fivbers. It is mainly used in concrete products including ornmental structures, fountains, domes etc.
Glass fiber reinforced concrete
Polypropylene fiber reinforced
Natural fiber reinforced concrete
According to the assumptions of Teraghi's one- Dimensiomal consolidation Theory which of the following statements is/are incorrect?
_is the normal stress when it acts into the area.
Shear stress
Torsional stress
Compressive stress
Tensile stress
According to the soil Mechanics, which type of soil is not fully consolidated under the existing overburden pressure
Compressed soil
Normally consolidated soil
Under-consolidated soil
Per-cnsolidated soil
A 8mm thick copper sheet is cut with a 9 cm diameter round punch. if the punch exerts a force of 16 KN, Find the sgear stress in the sheet
9.80 MPa
11.43 MPa
7.08 MPa
17.86 MPa
Assume L is the load in Newton and A is cross-sectional area, then stress(denoted by s) is equal to:
s= A+L
s= A*L
s= L/A
s=A/L
Is the algebraic sum of the moments of the forces on either side of the section of a loaded beam
Retaining walls
Mouduls of Resilience
Shearing foce
Bending moment
In which type of foundation the length is considerably greater than its width?
Raft foundation
pile foundation
Footing
Strip foundation
Which term is appropriate for the branch of physical geography which deals with the origin distribution of water on the earth surface?
Oxidtion
Hydropethia
Hydrology
Hydrolysis
Which onr of the following is not among the types of signals classified on the basis of their function?
Shuntung singnals
semaphore signals
Advance starter signls
Warner signals
Wich of the follwing statement is/are not among the major limitations of sprinkler irrihagation?
strong wind fisturbs the sptinkling
It minimizes the erosion of the soil
An activated carbon is specially treated carbon which has the property of absorbing and attracting impurities. Which of the follwing points is/are not among advantang of activated carbon?
It accelerate the ciagulation
Its overdose is harmful
A 10 m aluminum flagpole is installed at 30°C.After 2 days , the temperature drops to - 10°CHow much does the height change of the flagpole (in mm)?
(Assume thermal expansion coefficient for aluminm
7.8 mm
8.8 mm
9.5 mm
9.2 mm
A surveyor assumes P as difference in elevation between points X and Y having slips.what will be the expression to calculate slop correction ?
P2/2S
P2/4S
S2/2P
P/2S2
A soil engineer collects a sample of soil having moist unit weight of a soil is 24.5 KN/m3, water content available is 10% and the specific gravity of the solid of the soil is 2.50 .What is the degree of saturation of the soil ? ( Assume unit weight of water = 9.81 KN /m3)
250%
225%
75%
150%
What is the main disadvantage of Aeration process?
Excessive aeration absorb too much carbon dioxide and water becomes corrosive .
Excessive aeration absorb too much oxigen and thus water becomes corrosive .
It removes oils and decomposes algae and other aquatic product from water .
It effectively removes volatile gases which is harmful for water .
The ratio of lateral strain to that of longitudinal strain which remain constant within elastic limit is called as ____________
Modulus of rigidity
Hook's law
Young's modulus
Poisson's ratio
_____________ is the rigid dam which is constructed either with stone or brick masonry or mass concrete.
Solid gravity dam
Footing dam
Buttress dam
Sediment dam
Which one of the following formulas is correct to express the bond stress (Bs) ? Assume shear force at the section = Q .Lever arm = Jd and sum of the perimeter of bars = s .
Bs = Q/(Jd+S )
Bs = Jd /(Q*S)
Bs =Q /(Jd*S)
Bs= S/( Jd*Q)
Which among the following is /are the correct assumptions made in torsion formula ?
A . Material of the shaft is uniform throughout .
B. Twist along the shaft is uniform .
C .plane sections before twisting remain circular even after twisting .
D.Circular sections before twisting remain circular even after twisting .
A,B,C and D
C and D
There are three distinct stages occur in the natural process of sludge digestion due to biological action .what is the name of the first stage in which fresh sewerage -sludge is acted upon by anaerobic and facultative becteria' s which decompose easily available food matters ?
Acide regression
Acid fermentation
Alkaline fermentation
Chamber fermentation
Which of the following is /are the property (s)/of good quality of stones ?
A. Crushing strength greater than 1000 kg /cm2
B. Specific gravity should be greater then 8
C .stones should be well seasoned before putting into use .
Only B
______________ is a mechanical property of linear elastic solid materials which defines the relationship between stress and strain in a material
Lateral modulus
Bulk modulus
Which of the following typs of chemical weathering is associated with the feldspar , which can be found in granite changing to clay ?
Oxidation
Carbonation
Which one of the following is not the cause of buckling ?
Due to welded rails on weak tracks
Insufficient expansion gaps at rail joints
Due to excess tightening of bolts of the fish plates
Due to contraction of rail tracks in winter
A 10 inch long silver wire is stretched to a total length of 11.50 inches . Find the value of strain .
0.015
0.15
0.25
0.025
A 58 KN compressive load is applied to a 7 cm diameter , 2cm tall , aluminium cylinder calculate value of stress in MPa
20.80 MPa
16.50 MPa
15.08 MPa
20.08 MPa
At constant temperature, the fluid whose viscosity does not change with the rate of deformation, is called:
Real fluid
Non-Newtonian fluid
Ideal fluid
Newtonian fluid
Which constituent of good brick earth added in small quantity during the manufacturing of bricks, to give yellow tint to bricks and decrease shrinkage?
Magnesia
Oxide of iron
Silica
Alumina
As per the specifications designed by the Railway Board for trunk routes on Broad gauge tracks, the design speed for new track is _________and the maximum speed permissibleis__________.
160 km/hr, 120 km/hr
200 km/hr, 120 km/hr
180 km/hr, 150 km/hr
200 km/hr, 150 km/hr
Assume initial void ratio = e0, final void ratio = e. initial pressure=p0 and final pressure=p. Then, what is the value of coefficient of compressibility (av)?
av=(e-e0)/(p-p0)
av=(e0-e)/(p-p0)
av=(e0-e)/(p0-p)
av=(e0+e)/(p+p0)
A soil engineer collects a sample of soil which having moist unit weight of a soil is 25 kN/m3, water content available is 50% and the specific gravity of the solid of the soil is 2.55. Then, what is the value of porosity of soil mass? (Assume unit weight of water = 9.81 kM/m3)
30%
33%
66%
40%
Calculate the approximate specific energy of a trapezoidal channel having a bottom width of 6 metres, ratio of side slopes is 1:1 and the depth of flow at a dischage speed of 15 cubic metres per second is 1.5 metres.
2.6
1.6
3.6
4.6
Void ratio is the ratio of the volume of the voids to the volume of the soil soilds and Porosity of the soil mass is the ratio of the volume of voids to the total volume of the given soil. What would be the expression to relate these two terms?
(Assume void ratio = e and porosity= n)
n = ( e + 1)/e
e = n/(1+n)
n= e/(1+e)
n = 2e2/(1+e )
What value of tensile stress is required to produce a strain of 10 x 10-4 in copper? find the result in Mpa. ( Assume Young's modulus of copper = 50 GPa )
150 MPa
50 MPa
200 MPa
500 MPa
What would be the approximate weight of rail required for a particular track if the weight of locomotive axle load is 15000 tonnes?
25410 tonnes
39410 tonnes
29410 tonnes
35410 tonnes
An open cylindrical tank of 2 m diameter and 4 m high. contains watger up to 1.5 m depth If the cyclinder rotates about vertical axis. what angular velocity can be attained without spilling any water ?
12.9 radians/sec
10.9 radians/sec
9.9 radians/sec
11.1 radians/sec
To what reading should the line of collimation be adjusted when the insrtument was at Q?
1.146 m
0.946 m
1.246 m
0.786 m
The four kinds of crystals in thin sections of cement clinkers, name by Tornebohm are Alite, Belite, Celite and ______________ .
Elite
Delite
Gelite
Felite
Soil scientist collects unsaturated 200 cm3 sample of soil having weight 200 g. If the dried weight of soil is 180 g. Then, find the water containt available in the soil.
0.222
0.176
0.133
0.166
In which type of joint, plates to be fastened are placed one over the other and riveted by one or more rows of rivets?
Chain joint
Butt joint
Zig - Zag joint
Lap joint
According to Hook's law. A material is said to be elastic if it returns to its original, unloaded dimendions when load is removed. It can be expressed as:
stress / strain = constant
stress / strain = force
stress + strain = constant
stress - strain = constant
When a liquid rotates at constant angular velocity about a vertical axis of a rigid body
the pressure varies as the square of the radial distance
the velocity vector remains constant at apoint
the velocity vector varies inversly as the altitude along any vertical line
the pressure varies inversely as the altitude along any vertical line
According to geological classification. rocks are divided into three different categories i. e, Igneous rocks, Sedimentary rocks and Metamorphic rocks. In which category Granite, Basalt and Dolerite etc types of rocks fall?
Igneous rocks
Which of the following typical arrangements of points and crossings is being drawn in the figure shown above?
Tandem
Cross over
Symmetrical split
Double junction
Which apparatures is used to perform the soundness test of cement?
Le - chatlier apparatus
Vee - bee apparatus
Slump apparatus
Compaction apparantus
___________________ is used in concrete to provide economy in the cost of meterial. it is used as filler only and do not react with cement and water.
Sulphate resistant cement
Aggregate
Pozzolana
A surveyor made an error during the survey of a projet which is associated with his skills and vigilance. Which type of error this surveyor has committed?
Random errors
Systematic errors
Constant errors
Blunders
If R is the radius of the curve in metres and C is the chord length in metres what should be the expression to denote versine 'V' in millimetres?
V = 127 C2/ R
V = 127 R2/C
V = 125 C2/ R
V = 125 R2/C